 |
Standard Bore Irons |
|
|
|
Standard Bore Irons |
|
| Vendor | Trim Code | #1 | #2 | #3 | #4 | #5 | #6 | #7 | #8 | #9 | Wedge |
| Aldila | A1 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | ||
| A2 | 2.0 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 | 5.5 | 6.0 | |
| FST | F1 | 0 | 5/8 | 1.25 | 1 7/8 | 2.5 | 3 1/8 | 3.75 | 4 3/8 | 5.0 | 5.0 |
| F2 | 1 | 1 5/8 | 2.25 | 2 7/8 | 3.5 | 4 1/8 | 4.75 | 5 3/8 | 6.0 | 6.0 | |
| F3 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.0 | |||
| F4 | 1 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.0 | |||
| F5 | Do not butt trim. Tip trim only to final length. | ||||||||||
| Graman | Click Here | ||||||||||
| Graphite Design | G3 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.0 | ||
| G4 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 4.5 | |||
| Grafalloy | G5 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.25 |
| G6 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 | 5.5 | 6.0 | 6.25 | |
| Matrix | M1 | 0 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 3.5 |
| Makers Pride | M2 | 0 | 0 | 0 | .25 | .5 | .75 | 1.0 | 1.25 | 1.5 | 1.75 |
| M3 | .5 | .75 | 1.0 | 1.25 | 1.5 | 1.75 | 2.0 | 2.25 | 2.5 | 2.75 | |
| Paragon | P1 | 1.0 | 1.0 | 1.0 | 1.0 | 1.0 | 1.0 | 1.0 | 1.0 | 1.0 | 1.0 |
| Rifle | R1 | 0 | 9/16 | 1 1/8 | 1 11/16 | 2.25 | 2 13/16 | 3 3/8 | 3 15/16 | 4.5 | 5 1/16 |
| True Temper | T1 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.25 |
| T2 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 | 5.25 | |
| T3 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 | 5.5 | 6.0 | 6.5 | 7.0 | 7.25 | |
| T4 | 2,0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 | 5.5 | 6.0 | 6.25 | |
| UST | U1 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.0 |
| U2 | 1 | 1.5 | 2.0 | 2.5 | 3.0 | 3.5 | 4.0 | 4.5 | 5.0 | 5.0 | |
| U3 | 0 | .5 | 1.0 | 1.5 | 2.0 | 2.5 | 3.0 | 3.0 | |||
| All Iron Shafts | BI | Do not tip trim. Butt trim only to final length. | |||||||||
Special Note: If you would like to print a copy of the trimming instructions needed, see Catalog Downloads on Home Page
